top of page
Coating Thickness Gauge
Devices such as the coating thickness gauge, thickness metre, surface tester, and film check offered by Dhanbad Instruments are put to use for the purposes of material testing, quality control during the manufacturing, and automotive paint inspection. Look at a few coating thickness gauge, mil gauge, or paint metre products that are used to estimate nonmagnetic coating, protective layer, and dry film thickness (DFT) on ferrous and/or non-ferrous metal substrates like steel and aluminium without damaging them.
When anodizing, electrifying, or applying a zinc coating to metallic surfaces, a coating thickness gauge is a fundamental piece of equipment for confirming the quality of the finished product. A coating thickness check may also be used to measure the thickness and consistency of the body paint on used automobiles, which can reveal areas that have been repainted, identify hidden damage, and unearth previously unknown accidents. This information is important to consider when determining the true value of a car to be traded in. In a similar vein, some types of thickness checks may measure the thickness of dividers as well as determine the hardness of metals, plastics, and glass.
The use of an appealing or whirlpool current Thickness Measurement Equipment to check on powder-coated metal substrates is a good and reliable guideline for determining the thickness of the powder coating. An ultrasonic thickness check should be performed on powder-coated non-metal substrates such as plastic and wood. The term "coating thickness gauge" is synonymous with "dry film thickness gauge," "plating thickness tester," "coating thickness tester," "paint thickness measurement," "thickness measurement tool," "thickness tester," and a variety of other names.
Coating Thickness Gauge suppliers in Jharkhand and Bihar | Coating Thickness Gauge suppliers in Jharkhand and Bihar | Coating Thickness Gauge suppliers in India | Coating Thickness Gauge suppliers in India | Material Tester Suppliers in India | NDT Tester Suppliers in India | Thickness Meter Suppliers in India | Automotive Tester Suppliers in India | Surface Tester Suppliers in India | Thickness Gauge Suppliers in India | Paint Thickness Gauge Suppliers in India
Atomic Absorption Spectrophotometer | Digital Multimeter | Concrete Moisture Meter | Gloss Meter | Gas Detector | High-Speed Camera | Infrared Thermometer | Microscope | pH Meter | Particle Counter | Power Supply Unit | Paperless Recorder | Spectrophotometer | Torque Meter | Thermometer | Viscometer | Water Analysis Meter | Coating Thickness Gauge |
Coating Thickness Gauge
Coating Thickness Gauge PCE-CT 24FN
The thickness gauge PCE-CT 24FN is a mobile device for the fast and precise determination of eg ink layer thicknesses. With this thickness gauge layer thickness measurements on ferrous and non-ferrous metals can be performed. The measured value is displayed directly on the LC display of the thickness gauge. Thanks to the built-in memory of the thickness gauge and the advanced functions, statistics can be recorded. These statistics can be evaluated directly on the thickness gauge. When evaluating the recorded statistics in the thickness gauge, you can choose between a tabular and a graphical view.
The replaceable batteries can be recharged directly via the thickness gauge. Charging the batteries is possible via a USB port, for example via a computer. Even during the charging process, all functions of the thickness gauge are available. If the thickness gauge is not used, the meter will switch itself off automatically within the set time. This protects the batteries and ensures that the meter is ready for use the next time. Thus, the thickness gauge is also suitable for mobile use.
- Data memory for later evaluations
- Rechargeable batteries
- For ferrous and non-ferrous metals
- Alarm when limit value exceeded
- Statistics function for analyzing a test object
- Alignment sensor for turning the display
- Measuring range 0 ... 1500 μm
- Graphic representation of the measured values
Specifications
Measuring range 0 ... 1500 μm / 0 ... 59 mil / 0 ... 1.5 mm
Resolution 0.1 μm (at <100 μm)
1 μm (at> 100 μm)
0.001 mm
0.1 mil
Accuracy ± 5 μm (at <150 μm)
± 3% + 1 μm (at> 150 μm)
Smallest diameter (Fe) 12 mm
Smallest thickness (Fe) 0.5 mm
Curve wheel. minute (Fe) Convex. 2 mm; concave: 11 mm
Smallest diameter (nFe) 50
Smallest thickness (nFe) 0.5 mm
Storage 100 groups of 15 readings each
Display 2.25 inch LC display
Ambient temperature 0 ... 50°C / 32 ... 122°F
Power supply (batteries) 3 x 1.2V AA Ni-MH 800 mAh
Power supply (power supply) Primary: 100 ... 240V; 50/60 Hz; 0.45 A
Secondary side: 5V DC; 1 A
Dimensions 70.3 x 38.6 x 149.59 mm / 2.8 x 1.5 x 5.9 in
Weight Approx. 136.9 g / < 1 lb with batteries
Delivery Scope
1 x Coating thickness gauge PCE-CT 24FN
6 x Different reference foils
1 x Set of calibration standards (Fe and NFe)
3 x 1.2V batteries
1 x Micro-USB cable
1 x USB power plug
1 x Carrying case
1 x User manual
The replaceable batteries can be recharged directly via the thickness gauge. Charging the batteries is possible via a USB port, for example via a computer. Even during the charging process, all functions of the thickness gauge are available. If the thickness gauge is not used, the meter will switch itself off automatically within the set time. This protects the batteries and ensures that the meter is ready for use the next time. Thus, the thickness gauge is also suitable for mobile use.
- Data memory for later evaluations
- Rechargeable batteries
- For ferrous and non-ferrous metals
- Alarm when limit value exceeded
- Statistics function for analyzing a test object
- Alignment sensor for turning the display
- Measuring range 0 ... 1500 μm
- Graphic representation of the measured values
Specifications
Measuring range 0 ... 1500 μm / 0 ... 59 mil / 0 ... 1.5 mm
Resolution 0.1 μm (at <100 μm)
1 μm (at> 100 μm)
0.001 mm
0.1 mil
Accuracy ± 5 μm (at <150 μm)
± 3% + 1 μm (at> 150 μm)
Smallest diameter (Fe) 12 mm
Smallest thickness (Fe) 0.5 mm
Curve wheel. minute (Fe) Convex. 2 mm; concave: 11 mm
Smallest diameter (nFe) 50
Smallest thickness (nFe) 0.5 mm
Storage 100 groups of 15 readings each
Display 2.25 inch LC display
Ambient temperature 0 ... 50°C / 32 ... 122°F
Power supply (batteries) 3 x 1.2V AA Ni-MH 800 mAh
Power supply (power supply) Primary: 100 ... 240V; 50/60 Hz; 0.45 A
Secondary side: 5V DC; 1 A
Dimensions 70.3 x 38.6 x 149.59 mm / 2.8 x 1.5 x 5.9 in
Weight Approx. 136.9 g / < 1 lb with batteries
Delivery Scope
1 x Coating thickness gauge PCE-CT 24FN
6 x Different reference foils
1 x Set of calibration standards (Fe and NFe)
3 x 1.2V batteries
1 x Micro-USB cable
1 x USB power plug
1 x Carrying case
1 x User manual
Coating Thickness Gauge PCE-CT 80
The paint layer thickness gauge PCE-CT 80 is a measuring device for the nondestructive measurement of coatings (paints, lacquers, plastics ...) on steel / iron and non-ferrous metals. Thanks to the externally connected sensor on the PCE-CT 80 ink layer thickness gauge, even difficult-to-reach measuring points can be easily achieved. The menu navigation of the paint thickness gauge allows easy adjustment and setting to new parameters and makes this handy paint coating thickness gauge an indispensable tool for control measurements in production, workshop and quality assurance.
The color coating thickness gauge PCE-CT 80 is also ideally suited for detecting and assessing eg accident damage to motor vehicles immediately, but also in the industrial sector the paint thickness gauge can be optimally used in incoming and outgoing inspections as well as material testing in production.
The ergonomically shaped PCE-CT 80 ink layer thickness gauge with external sensor allows you to quickly determine measurement results with high accuracy. The paint thickness gauge measures non-magnetic layers such as paint, plastic, chrome, copper, zinc, enamel, etc. on steel / iron, and non-electrically conductive layers such as paint, plastic, enamel, paper, glass, rubber, etc. on copper, aluminum, brass and stainless steel, as well as anodized aluminum.
- For many materials such as, iron, steel, aluminum, copper, brass and stainless steel
- Measurements can not be influenced by vibrations
- Practical V-groove on the measuring heads
- Ergonomic design
- Warning for measurements outside the maximum measuring range
- Wear-resistant, spring-mounted measuring head for precise measurement results
- Incl. ISO laboratory calibration with certificate
- Various optional sensors available
Specifications
Measuring range Fe: 0 to 5000 μm / 0 ... 196.9 mils
NFe: 0 to 3000 μm / 0 ... 118.1 mils
Accuracy ± (2% of reading + 1 μm / 0.039 mils)
Resolution 0.1 μm (0.0039 mils) (< 100 μm / 3.94 mils)
1 μm / 0.039 mils (> 100 μm / 3.94 mils)
Measurable materials Non-magnetic layers on steel, iron, ...
Non-electrically conductive layers on aluminum, copper, ...
Min. Radius of curvature convex 5 mm / 0.2 in
Min. Radius of curvature concave 25 mm / 1 in
Min. Measuring surface Ø17 mm / 0.7 in
Min. Layer thickness 0.2 mm / 0.08 in (on magnetic materials)
0.05 mm / 0.002 in (on non-magnetic materials)
Probe mode Autom. Mode with material detection (Fe + NFe)
Magnetic mode (Fe)
Eddy current mode (NFe)
Measurement mode Single measurement
continuous measurement
Calibration Multipoint calibration (1 ... 4 points for each group)
Zeroing
Units μm, mm, mils
Data transfer USB 2.0
Storage A volatile measuring group (DIR mode)
Four measuring groups with autom. Storage and max. 2000 readings (GEN mode)
Statistical functions Number of Measured values, mean, minimum, maximum, standard deviation
Alarm Display when the adjustable upper and lower alarm limits are exceeded
Operating time Autom. Shutdown mode (3 min.)
Power supply 3 x 1.5V AAA batteries
Display 128 x 128 px LCD display
Indicators Battery status
Fault detection
Operating conditions 0 ... 50°C / 32 ... 122°F
20 ... 90% RH not condensing
Storage conditions -10 ... 60°C / 14 ... 140°F
20 ... 90% RH not condensing
Dimensions (L x W x H) 143 x 71 x 37 mm / 5.6 x 2.8 x 1.5 in
Weight With sensor and batteries: approx. 271 g / < 1 lb
Delivery Scope
1 x PCE-CT 80 Coating thickness gauge
1 x PCE-CT 80-FN1.5 sensor
3 x AAA batteries
1 x User manual
1 x Transport case
1 x Set of standard films
1 x Calibration plates (Fe and NFe)
1 x ISO calibration certificate
The color coating thickness gauge PCE-CT 80 is also ideally suited for detecting and assessing eg accident damage to motor vehicles immediately, but also in the industrial sector the paint thickness gauge can be optimally used in incoming and outgoing inspections as well as material testing in production.
The ergonomically shaped PCE-CT 80 ink layer thickness gauge with external sensor allows you to quickly determine measurement results with high accuracy. The paint thickness gauge measures non-magnetic layers such as paint, plastic, chrome, copper, zinc, enamel, etc. on steel / iron, and non-electrically conductive layers such as paint, plastic, enamel, paper, glass, rubber, etc. on copper, aluminum, brass and stainless steel, as well as anodized aluminum.
- For many materials such as, iron, steel, aluminum, copper, brass and stainless steel
- Measurements can not be influenced by vibrations
- Practical V-groove on the measuring heads
- Ergonomic design
- Warning for measurements outside the maximum measuring range
- Wear-resistant, spring-mounted measuring head for precise measurement results
- Incl. ISO laboratory calibration with certificate
- Various optional sensors available
Specifications
Measuring range Fe: 0 to 5000 μm / 0 ... 196.9 mils
NFe: 0 to 3000 μm / 0 ... 118.1 mils
Accuracy ± (2% of reading + 1 μm / 0.039 mils)
Resolution 0.1 μm (0.0039 mils) (< 100 μm / 3.94 mils)
1 μm / 0.039 mils (> 100 μm / 3.94 mils)
Measurable materials Non-magnetic layers on steel, iron, ...
Non-electrically conductive layers on aluminum, copper, ...
Min. Radius of curvature convex 5 mm / 0.2 in
Min. Radius of curvature concave 25 mm / 1 in
Min. Measuring surface Ø17 mm / 0.7 in
Min. Layer thickness 0.2 mm / 0.08 in (on magnetic materials)
0.05 mm / 0.002 in (on non-magnetic materials)
Probe mode Autom. Mode with material detection (Fe + NFe)
Magnetic mode (Fe)
Eddy current mode (NFe)
Measurement mode Single measurement
continuous measurement
Calibration Multipoint calibration (1 ... 4 points for each group)
Zeroing
Units μm, mm, mils
Data transfer USB 2.0
Storage A volatile measuring group (DIR mode)
Four measuring groups with autom. Storage and max. 2000 readings (GEN mode)
Statistical functions Number of Measured values, mean, minimum, maximum, standard deviation
Alarm Display when the adjustable upper and lower alarm limits are exceeded
Operating time Autom. Shutdown mode (3 min.)
Power supply 3 x 1.5V AAA batteries
Display 128 x 128 px LCD display
Indicators Battery status
Fault detection
Operating conditions 0 ... 50°C / 32 ... 122°F
20 ... 90% RH not condensing
Storage conditions -10 ... 60°C / 14 ... 140°F
20 ... 90% RH not condensing
Dimensions (L x W x H) 143 x 71 x 37 mm / 5.6 x 2.8 x 1.5 in
Weight With sensor and batteries: approx. 271 g / < 1 lb
Delivery Scope
1 x PCE-CT 80 Coating thickness gauge
1 x PCE-CT 80-FN1.5 sensor
3 x AAA batteries
1 x User manual
1 x Transport case
1 x Set of standard films
1 x Calibration plates (Fe and NFe)
1 x ISO calibration certificate
Coating Thickness Gauge PCE-CT 26FN
The coating thickness gauge PCE-CT 26FN can measure non-destructive coatings (paints, plastics ...) on steel / iron and non-ferrous metals. The coating thickness gauge is ideally suited, for example, to detect accidental damage to the vehicle immediately. But also in the industrial sector, the PCE-CT 26FN coating thickness gauge is used for incoming and outgoing inspection in order to be able to offer consistently consistent product qualities.
The ergonomically shaped coating thickness gauge with integrated probe and very simple operation allows you to quickly determine measurement results with high accuracy. The coating thickness gauge PCE-CT 26FN is designed for measurements of non-magnetic coatings such as lacquer, plastic, chrome, copper, zinc, enamel, etc. on steel and iron, as well as all insulating coatings such as lacquer, plastic, enamel, paper, glass, rubber etc. on copper, aluminum, brass, stainless steel and aluminum.
Application / use:
Simply place the coating thickness gauge u. read the measured value. You can easily measure varnish and paint layers, plastic layers, chrome layers, copper plating, zinc layers, galvanizing, enamel ... on steel, stainless steel, iron and similar materials. Non-ferrous metals (copper, aluminum, brass) and anodized aluminum.
By means of the included standards you can adjust the coating thickness gauge at any time. To do this, the coating thickness gauge must be placed on one of the foils. Please make sure that the meter is seated straight / level.
- Immediately ready to measure
- Wear-resistant sensor
- V-groove for measurement on pipes
- One-handed operation
- ISO calibration optional
- Incl. transport case
Specification
Measuring range 0 ... 1250 μm (0 ... 49.2 mils)
Resolution 1 μm (0.039 mils)
Accuracy ± (3% + 2 μm) or ± (3% + 0.079 mils)
Smallest measuring surface 5 x 5 mm / 0.2 in x 0.2 in
Smallest radius of curvature Convex. 3 mm (0.1 in) / concave: 50 mm (2 in)
Smallest thickness of the base material Fe: at least 0.5 mm / 0.02 in
NFe: at least 0.3 mm / 0.01 in
Display OLED display
Ambient temperature 0 ... 50°C / 32 ... 120°F
Power supply 2 x AAA battery 1.5V
Dimension 100 x 52 x 29 mm / 4 x 2 x 1.1 in
Weight About 68 g / < 1 lb (without batteries)
Delivery Scope
1 x Coating thickness gauge PCE-CT 26FN
2 x AAA batteries 1.5V
1 x Set of calibration foils (5 pieces)
1 x Fe standard block
1 x NFe standard block
1 x Transport case
1 x User manual
The ergonomically shaped coating thickness gauge with integrated probe and very simple operation allows you to quickly determine measurement results with high accuracy. The coating thickness gauge PCE-CT 26FN is designed for measurements of non-magnetic coatings such as lacquer, plastic, chrome, copper, zinc, enamel, etc. on steel and iron, as well as all insulating coatings such as lacquer, plastic, enamel, paper, glass, rubber etc. on copper, aluminum, brass, stainless steel and aluminum.
Application / use:
Simply place the coating thickness gauge u. read the measured value. You can easily measure varnish and paint layers, plastic layers, chrome layers, copper plating, zinc layers, galvanizing, enamel ... on steel, stainless steel, iron and similar materials. Non-ferrous metals (copper, aluminum, brass) and anodized aluminum.
By means of the included standards you can adjust the coating thickness gauge at any time. To do this, the coating thickness gauge must be placed on one of the foils. Please make sure that the meter is seated straight / level.
- Immediately ready to measure
- Wear-resistant sensor
- V-groove for measurement on pipes
- One-handed operation
- ISO calibration optional
- Incl. transport case
Specification
Measuring range 0 ... 1250 μm (0 ... 49.2 mils)
Resolution 1 μm (0.039 mils)
Accuracy ± (3% + 2 μm) or ± (3% + 0.079 mils)
Smallest measuring surface 5 x 5 mm / 0.2 in x 0.2 in
Smallest radius of curvature Convex. 3 mm (0.1 in) / concave: 50 mm (2 in)
Smallest thickness of the base material Fe: at least 0.5 mm / 0.02 in
NFe: at least 0.3 mm / 0.01 in
Display OLED display
Ambient temperature 0 ... 50°C / 32 ... 120°F
Power supply 2 x AAA battery 1.5V
Dimension 100 x 52 x 29 mm / 4 x 2 x 1.1 in
Weight About 68 g / < 1 lb (without batteries)
Delivery Scope
1 x Coating thickness gauge PCE-CT 26FN
2 x AAA batteries 1.5V
1 x Set of calibration foils (5 pieces)
1 x Fe standard block
1 x NFe standard block
1 x Transport case
1 x User manual
Coating Thickness Gauge PCE-CT 100
PCE-CT 100 is a coating thickness measuring instrument used to quickly and easily determine coating thicknesses on ferrous (Fe) and non-ferrous (nFe) metals. This compact handheld coating thickness gauge uses magnetic induction (ISO 2178) and eddy current (ISO 2360) coating thickness measurement methods to take non-destructive measurements of coating and dry film thickness (DFT) on metal substrates such as steel and aluminum.
When accompanied by an external sensor probe (sensor probes sold separately - see accessories), this coating thickness gauge is ideal for painted and powder-coated surface testing, automotive and aircraft surface finish inspections, primed and coated materials testing, and manufacturing quality control applications. Alarm limits can be set in the coating thickness gauge to notify the user when a coating is too thick or too thin. If a coating thickness measurement falls outside the established limits, the device produces a visual and audible signal.
- Uses magnetic induction (ISO 2178) and eddy current (ISO 2360) coating thickness measurement methods
- Measures coating thickness on ferrous (Fe) and non-ferrous (nFe) metals
- Designed for non-destructive testing and inspection
- Saves up to 100,000 measurements to memory
- Data transfer via USB or Bluetooth interfaces
- Displays measuring units in μm, mm or mils
- Programmable alarm limits
- High measuring accuracy
- Two-point calibration
- High resolution
- Includes factory calibration certificate according to ISO 9001
- Sensor probes sold separately
Specifcations
Resolution
0.1 or < 0.2% of the measured value
(for probes with a measuring range of up to 1500 μm / 1.5 mm / 59 mil)
1 or < 0.2% of the measured value
(for probes with a measuring range of more than 1500 μm / 1.5 mm / 59 mil)
Display High-resolution color display, backlit
Measuring units μm, mm or mils
Menu languages English, German, French, Italian, Spanish, Turkish, Czech, Chinese
Storage Direct mode: Max. 1,000 measured values in Fe (Type F) and nFe (Type N) mode
File memory: Max. 100,000 measured values
Calibration Factory calibration
Zero (one-point calibration)
One-foil calibration (two-point calibration)
Two-foil calibration
Cal-through-coat calibration
Zero offset Addition of a constant value to the measured value
Statistics parameters N, x̅¯, σ, Max, Min, Cp, Cpk, Kvar
On-screen statistics displayed x̅¯, σ, Max, Min
Alarm limits
Programmable with visual and audible signaling
Interfaces USB 2.0, Bluetooth 4.0
Operating temperature 0 ... 50°C / 32 ... 122°F
Power supply 3 x 1.5V AA batteries
Dimensions Approx. 163 x 82 x 40 mm / 6.42 x 3.23 x 1.58 in (H x W x D)
Weight Approx. 290 g / 0.64 lb (including batteries)
Ingress protection rating IP52 (protection against dust and dripping water)
Delivery Scope
1 x PCE-CT 100 coating thickness gauge
3 x 1.5V AA batteries
1 x USB cable
1 x PC-compatible software
1 x Factory calibration certificate according to ISO 9001
1 x User manual
1 x Carrying case
Note: Sensor probes sold separately
When accompanied by an external sensor probe (sensor probes sold separately - see accessories), this coating thickness gauge is ideal for painted and powder-coated surface testing, automotive and aircraft surface finish inspections, primed and coated materials testing, and manufacturing quality control applications. Alarm limits can be set in the coating thickness gauge to notify the user when a coating is too thick or too thin. If a coating thickness measurement falls outside the established limits, the device produces a visual and audible signal.
- Uses magnetic induction (ISO 2178) and eddy current (ISO 2360) coating thickness measurement methods
- Measures coating thickness on ferrous (Fe) and non-ferrous (nFe) metals
- Designed for non-destructive testing and inspection
- Saves up to 100,000 measurements to memory
- Data transfer via USB or Bluetooth interfaces
- Displays measuring units in μm, mm or mils
- Programmable alarm limits
- High measuring accuracy
- Two-point calibration
- High resolution
- Includes factory calibration certificate according to ISO 9001
- Sensor probes sold separately
Specifcations
Resolution
0.1 or < 0.2% of the measured value
(for probes with a measuring range of up to 1500 μm / 1.5 mm / 59 mil)
1 or < 0.2% of the measured value
(for probes with a measuring range of more than 1500 μm / 1.5 mm / 59 mil)
Display High-resolution color display, backlit
Measuring units μm, mm or mils
Menu languages English, German, French, Italian, Spanish, Turkish, Czech, Chinese
Storage Direct mode: Max. 1,000 measured values in Fe (Type F) and nFe (Type N) mode
File memory: Max. 100,000 measured values
Calibration Factory calibration
Zero (one-point calibration)
One-foil calibration (two-point calibration)
Two-foil calibration
Cal-through-coat calibration
Zero offset Addition of a constant value to the measured value
Statistics parameters N, x̅¯, σ, Max, Min, Cp, Cpk, Kvar
On-screen statistics displayed x̅¯, σ, Max, Min
Alarm limits
Programmable with visual and audible signaling
Interfaces USB 2.0, Bluetooth 4.0
Operating temperature 0 ... 50°C / 32 ... 122°F
Power supply 3 x 1.5V AA batteries
Dimensions Approx. 163 x 82 x 40 mm / 6.42 x 3.23 x 1.58 in (H x W x D)
Weight Approx. 290 g / 0.64 lb (including batteries)
Ingress protection rating IP52 (protection against dust and dripping water)
Delivery Scope
1 x PCE-CT 100 coating thickness gauge
3 x 1.5V AA batteries
1 x USB cable
1 x PC-compatible software
1 x Factory calibration certificate according to ISO 9001
1 x User manual
1 x Carrying case
Note: Sensor probes sold separately
Coating Thickness Gauge PCE-CT 65
PCE-CT 65 is a coating thickness gauge that uses magnetic induction (ferrous) or eddy current (non-ferrous) to take non-destructive measurements of coating and dry film thickness (DFT) on metal substrates such as steel and aluminum. This thickness gauge is ideal for painted and powder-coated surface testing, automotive paint inspection, coated material testing, and manufacturing quality control applications.
The easy-to-use downloadable PC-compatible software included with this thickness gauge allows for detailed analysis of measurement results via computer. Measurement values are shown in a table and different working modes can be selected for data filtering. Statistics include the maximum, minimum and average value per working group. Statistics can be divided by ferrous and non-ferrous material. The software also counts how many readings have been stored in each material group. For more details, please refer to the user manual.
- Includes calibration shims and blocks for DIY accuracy testing, a carrying case for easy transport, and a 2-year warranty against manufacturer defects
- Optional ISO calibration certificate available for purchase separately - see accessories tab for details
- Features two measuring modes (ferrous and non-ferrous) with integrated sensors for comfortable, one-handed operation
- Saves up to 1500 measurements to memory
- Comes with a USB cable and downloadable PC software (see downloads tab) for detailed analysis of measurement results via computer
- Incl. ISO Calibration Certificate
Specification
Principle Magnetic induction
Measuring range 0 ... 1350 µm / 0 ... 53.1 mils
Accuracy 0 ... 1000 µm: (±2.5 % ±2 µm)
1000 µm ... 1350 µm: ±3.5 %
0 ... 39.3 mils: (±2 % ±0.08 mils)
39.3 mils ... 53.1 mils: ±3.5 %
Resolution 0 ... 100 µm: 0.1 µm
100 µm ... 1000 µm: 1 µm
in 1000 mm ... 1350 µm: 0.01 mm
0 ... 10 mils: 0.01 mils
10 mils ... 53.1 mils: 0 ... 1 mils
Smallest surface Ø 7 mm / Ø 0.3 in
Min. curvature radius 1.5 mm / 0.05 in
Min. substrate thickness 0.5 mm / 0.02 in
Non-ferrous metals
Principle Eddy current
Measuring range 0 ... 1350 µm / 0 ... 53.1 mils
Accuracy 0 ... 1000 µm: ±(2.5 % ±2 µm)
1000 µm ... 1350 µm: ±3.5 %
0 ... 39.3 mils: ±(2 % ±0.08 mils)
39.3 mils ... 53.1 mils: ±3.5 %
Resolution 0 ... 100 µm: 0.1 .mu.m
100 µm ... 1000 µm: 1 µm
in 1000 mm ... 1350 µm: 0.01 mm
0 ... 10 mils: 0.01 mils
10 mils ... 53.1 mils: 0 ... 1 mils
Smallest surface Ø 5 mm / Ø 0.2 in
Min. curvature radius 3 mm / 0.1 in
Min. substrate thickness 0.3 mm / 0.01 in
Units µm, mils
Functions Alarm function, display lighting, automatic shutdown, calibration, memory function
Memory option 30 storage groups with a capacity of 50 measurements each = 1500 measurements total
Interface USB
Environmental conditions 0 ... 40°C / 32° F ... 104°F, 20% ... 90% rh
Power supply 2 x 1.5V AAA batteries
Delivery Scope
1 x PCE-CT 65 Coating thickness gauge
2 x 1.5V AAA batteries
5 x Calibration shims
2 x Calibration blocks (aluminum and iron)
1 x USB cable
1 x User manual
1 x Carrying case
1 x ISO calibration certificate
The easy-to-use downloadable PC-compatible software included with this thickness gauge allows for detailed analysis of measurement results via computer. Measurement values are shown in a table and different working modes can be selected for data filtering. Statistics include the maximum, minimum and average value per working group. Statistics can be divided by ferrous and non-ferrous material. The software also counts how many readings have been stored in each material group. For more details, please refer to the user manual.
- Includes calibration shims and blocks for DIY accuracy testing, a carrying case for easy transport, and a 2-year warranty against manufacturer defects
- Optional ISO calibration certificate available for purchase separately - see accessories tab for details
- Features two measuring modes (ferrous and non-ferrous) with integrated sensors for comfortable, one-handed operation
- Saves up to 1500 measurements to memory
- Comes with a USB cable and downloadable PC software (see downloads tab) for detailed analysis of measurement results via computer
- Incl. ISO Calibration Certificate
Specification
Principle Magnetic induction
Measuring range 0 ... 1350 µm / 0 ... 53.1 mils
Accuracy 0 ... 1000 µm: (±2.5 % ±2 µm)
1000 µm ... 1350 µm: ±3.5 %
0 ... 39.3 mils: (±2 % ±0.08 mils)
39.3 mils ... 53.1 mils: ±3.5 %
Resolution 0 ... 100 µm: 0.1 µm
100 µm ... 1000 µm: 1 µm
in 1000 mm ... 1350 µm: 0.01 mm
0 ... 10 mils: 0.01 mils
10 mils ... 53.1 mils: 0 ... 1 mils
Smallest surface Ø 7 mm / Ø 0.3 in
Min. curvature radius 1.5 mm / 0.05 in
Min. substrate thickness 0.5 mm / 0.02 in
Non-ferrous metals
Principle Eddy current
Measuring range 0 ... 1350 µm / 0 ... 53.1 mils
Accuracy 0 ... 1000 µm: ±(2.5 % ±2 µm)
1000 µm ... 1350 µm: ±3.5 %
0 ... 39.3 mils: ±(2 % ±0.08 mils)
39.3 mils ... 53.1 mils: ±3.5 %
Resolution 0 ... 100 µm: 0.1 .mu.m
100 µm ... 1000 µm: 1 µm
in 1000 mm ... 1350 µm: 0.01 mm
0 ... 10 mils: 0.01 mils
10 mils ... 53.1 mils: 0 ... 1 mils
Smallest surface Ø 5 mm / Ø 0.2 in
Min. curvature radius 3 mm / 0.1 in
Min. substrate thickness 0.3 mm / 0.01 in
Units µm, mils
Functions Alarm function, display lighting, automatic shutdown, calibration, memory function
Memory option 30 storage groups with a capacity of 50 measurements each = 1500 measurements total
Interface USB
Environmental conditions 0 ... 40°C / 32° F ... 104°F, 20% ... 90% rh
Power supply 2 x 1.5V AAA batteries
Delivery Scope
1 x PCE-CT 65 Coating thickness gauge
2 x 1.5V AAA batteries
5 x Calibration shims
2 x Calibration blocks (aluminum and iron)
1 x USB cable
1 x User manual
1 x Carrying case
1 x ISO calibration certificate
Coating Thickness Gauge PCE-CT 5000H
PCE-CT 5000H is a coating thickness measuring instrument used for the rapid determination of coating thicknesses on ferrous (Type F) and non-ferrous (Type N) metals. The coating thickness gauge automatically detects the type of metal to be measured. The PCE-CT 5000H coating thickness gauge uses magnetic induction (ferrous) or eddy current (non-ferrous) to take non-destructive measurements of coating and dry film thickness (DFT) on metal substrates such as steel and aluminum.
This thickness gauge is ideal for painted and powder-coated surface testing, automotive paint inspection, coated material testing, and manufacturing quality control applications. Alarm limits can be set in the coating thickness gauge to notify the user when a coating is too thick or too thin. If a coating thickness measurement falls outside the established limits, a message appears on the display to alert the user.
- Designed for non-destructive testing and inspection
- Measures coating thickness on Fe and nFe metals
- Displays measuring units in μm, mm or mils
- Saves up to 2000 measurements to internal memory
- Practical V-groove on the measuring head
- One- to four-point and zero calibration
- Comfortable one-handed operation
- Programmable alarm limits
- High measuring range
- High measuring accuracy
- Automatic shutdown
- Optional ISO calibration certificate available for purchase separately - see accessories tab for details
Specifications
Probe
Type F and Type N
Measuring range Type F 0 ... 5000 μm / 0 ... 5 mm / 0 ... 196 mils
Measuring accuracy Type F ± (2% + 1 μm)
Resolution Type F 0 ... 99.9 μm: 0.1 μm, 100 ... 999 μm: 1 μm
> 1000 μm: 0.01 mm
Measuring principle Type F Magnetic induction
Smallest thickness of the base material 0.02 mm
Measuring range Type N 0 ... 3000 μm / 0 ... 3 mm / 0 ... 118 mils
Measuring accuracy Type N ± (2% + 1 μm)
Resolution Type N 0 ... 99.9 μm: 0.1 μm, 100 ... 999 μm: 1 μm
> 1000 μm: 0.01 mm
Measuring principle Type N Eddy current
Smallest thickness of the base material 0.05 mm
Calibration One-point to four-point calibration, zero calibration
Data storage Direct measurement (no measurement data storage), four data groups (automatic measurement data storage of up to 2000 measured values)
Statistical functions Number of measurements, average, minimum, maximum, standard deviation
Measurement units μm, mm, mils
Alarm Alarm limits adjustable, alarm symbol is displayed when limits are exceeded
Minimum radius of curvature (convex) 5 mm / 0.2 in
Minimum radius of curvature (concave) 25 mm / 1 in
Smallest measuring surface Diameter of 20 mm / 0.8 in
Maximum measuring rate 2 x per second
Data interface Data transfer via USB
Power supply 2 x 1.5V AAA batteries
Menu languages German, English, Russian, Chinese
Operating conditions 0 ... 50°C / 32 ... 122°F, 20 ... 90% RH
Storage conditions -10 ... 60°C / 14 ... 140°F
Standards CE ROHS FCC
Dimensions 110 x 53 x 24 mm / 4.33 x 2.09 x 0.95 in
Material housing ABS plastic
Weight 92 g / < 1 lb
Delivery Scope
1 x PCE-CT 5000H coating thickness gauge
2 x Zero calibration plates (ferrous and non-ferrous)
5 x Calibration plates
2 x 1.5V AAA batteries
1 x USB cable
1 x PC-compatible software
1 x User manual
1 x Carrying case
This thickness gauge is ideal for painted and powder-coated surface testing, automotive paint inspection, coated material testing, and manufacturing quality control applications. Alarm limits can be set in the coating thickness gauge to notify the user when a coating is too thick or too thin. If a coating thickness measurement falls outside the established limits, a message appears on the display to alert the user.
- Designed for non-destructive testing and inspection
- Measures coating thickness on Fe and nFe metals
- Displays measuring units in μm, mm or mils
- Saves up to 2000 measurements to internal memory
- Practical V-groove on the measuring head
- One- to four-point and zero calibration
- Comfortable one-handed operation
- Programmable alarm limits
- High measuring range
- High measuring accuracy
- Automatic shutdown
- Optional ISO calibration certificate available for purchase separately - see accessories tab for details
Specifications
Probe
Type F and Type N
Measuring range Type F 0 ... 5000 μm / 0 ... 5 mm / 0 ... 196 mils
Measuring accuracy Type F ± (2% + 1 μm)
Resolution Type F 0 ... 99.9 μm: 0.1 μm, 100 ... 999 μm: 1 μm
> 1000 μm: 0.01 mm
Measuring principle Type F Magnetic induction
Smallest thickness of the base material 0.02 mm
Measuring range Type N 0 ... 3000 μm / 0 ... 3 mm / 0 ... 118 mils
Measuring accuracy Type N ± (2% + 1 μm)
Resolution Type N 0 ... 99.9 μm: 0.1 μm, 100 ... 999 μm: 1 μm
> 1000 μm: 0.01 mm
Measuring principle Type N Eddy current
Smallest thickness of the base material 0.05 mm
Calibration One-point to four-point calibration, zero calibration
Data storage Direct measurement (no measurement data storage), four data groups (automatic measurement data storage of up to 2000 measured values)
Statistical functions Number of measurements, average, minimum, maximum, standard deviation
Measurement units μm, mm, mils
Alarm Alarm limits adjustable, alarm symbol is displayed when limits are exceeded
Minimum radius of curvature (convex) 5 mm / 0.2 in
Minimum radius of curvature (concave) 25 mm / 1 in
Smallest measuring surface Diameter of 20 mm / 0.8 in
Maximum measuring rate 2 x per second
Data interface Data transfer via USB
Power supply 2 x 1.5V AAA batteries
Menu languages German, English, Russian, Chinese
Operating conditions 0 ... 50°C / 32 ... 122°F, 20 ... 90% RH
Storage conditions -10 ... 60°C / 14 ... 140°F
Standards CE ROHS FCC
Dimensions 110 x 53 x 24 mm / 4.33 x 2.09 x 0.95 in
Material housing ABS plastic
Weight 92 g / < 1 lb
Delivery Scope
1 x PCE-CT 5000H coating thickness gauge
2 x Zero calibration plates (ferrous and non-ferrous)
5 x Calibration plates
2 x 1.5V AAA batteries
1 x USB cable
1 x PC-compatible software
1 x User manual
1 x Carrying case
Coating Thickness Gauge PCE-CT 28
The PCE-CT 28 Coating Thickness Gauge for cars is for measuring the thickness of paint and plastic on ferrous or non-ferrous materials without damaging the coating's surface. The Coating Thickness Gauge stands out due to its high range of measurement. This Coating Thickness Gauge works excellently as a tool for technicians in areas of paint or lacquering such as in production, automotive body repair or quality control. The Coating Thickness Gauge is particularly useful in detecting damage to vehicles produced by an accident, for preventing possible damage or as a toll in auto body repair. Also, in the industrial sector, this device is essential for quality control in shipping and receiving and during production. It is ergonomic with an integrated sensor and it shows results of measurements quickly and accurately. The Coating Thickness Gauge was designed for non-magnetic coatings such as plastic, chrome, zinc, copper, etc. and insulation such as rubber, plastic, glass and paper over steel, iron, aluminium, brass and stainless steel. Thanks to its wide measurement range, the Coating Thickness Gauge is ideal for the naval and metal industries.
- F / N: for materials including iron, steel, aluminium, copper, brass and stainless steel
- Instant results
- Large measurement range
- Vibrations do not influence readings
- Elastic lined measuring head to ensure accurate results and prevent wear
- The v-slot simplifies the measurement on round surfaces acting as a reference or axis point
- Can be operated comfortably with only one hand thanks to its design and integrated sensor
- Incl. ISO Calibration Certificate
- Complete with battery, carrying case, calibration standards and user's manual
Specifications
Measurement range 0 ... 1250 µm / 49.2 mils
Resolution 0.1 µm / 0.004 mils (in a range of 0.0 to 99.9 µm / 3.9 mils)
1 µm / 0.04 mils(above the range)
Accuracy ±2 % or 2.5 µm / 0.10 mils (highest reading is valid)
Minimum surface measurable 6 mm x 6 mm / 0.2 in x 0.2 in
Minimum radial curve convexed: 5 mm / 0.2 in
concaved: 60 mm / 2.4 in
Minimum thickness of material 0.3 mm / 0.01 in (for ferrous materials)
0.1 mm / 0.004 in (for non-ferrous materials)
Display LCD with 4 mm x 10 mm (0.2 in x 0.4 in) high digits
Operating temperature 0 ... 50°C / 32 ... 122°F
Power 4 batteries
Dimensions 126 x 65 x 27 mm /
5.0 x 2.6 x 1.1 in
Weight 120 g / 0.26 lbs with batteries
Delivery Scope
1 x PCE-CT 28 Coating Thickness Gauge with integrated F/N sensor
1 x Carrying case
4 x Batteries
1 x Set of calibration standards
1 x User's manual
1 x ISO Calibration Certificate
Calibration certificates are issued specifically for the customer and are excluded from the right of return.
- F / N: for materials including iron, steel, aluminium, copper, brass and stainless steel
- Instant results
- Large measurement range
- Vibrations do not influence readings
- Elastic lined measuring head to ensure accurate results and prevent wear
- The v-slot simplifies the measurement on round surfaces acting as a reference or axis point
- Can be operated comfortably with only one hand thanks to its design and integrated sensor
- Incl. ISO Calibration Certificate
- Complete with battery, carrying case, calibration standards and user's manual
Specifications
Measurement range 0 ... 1250 µm / 49.2 mils
Resolution 0.1 µm / 0.004 mils (in a range of 0.0 to 99.9 µm / 3.9 mils)
1 µm / 0.04 mils(above the range)
Accuracy ±2 % or 2.5 µm / 0.10 mils (highest reading is valid)
Minimum surface measurable 6 mm x 6 mm / 0.2 in x 0.2 in
Minimum radial curve convexed: 5 mm / 0.2 in
concaved: 60 mm / 2.4 in
Minimum thickness of material 0.3 mm / 0.01 in (for ferrous materials)
0.1 mm / 0.004 in (for non-ferrous materials)
Display LCD with 4 mm x 10 mm (0.2 in x 0.4 in) high digits
Operating temperature 0 ... 50°C / 32 ... 122°F
Power 4 batteries
Dimensions 126 x 65 x 27 mm /
5.0 x 2.6 x 1.1 in
Weight 120 g / 0.26 lbs with batteries
Delivery Scope
1 x PCE-CT 28 Coating Thickness Gauge with integrated F/N sensor
1 x Carrying case
4 x Batteries
1 x Set of calibration standards
1 x User's manual
1 x ISO Calibration Certificate
Calibration certificates are issued specifically for the customer and are excluded from the right of return.
Coating Thickness Gauge PCE-CT 27FN
PCE-CT 27FN is a Coating Thickness Gauge that takes non-destructive measurements of nonmagnetic coating, insulating layer and dry film thickness (DFT) on metal substrates such as steel and aluminum. Ideal for surface testing, automotive paint inspection, material testing and manufacturing quality control applications, this Coating Thickness Gauge is designed to measure layers of paint, ink, plastic, chrome, copper, zinc, enamel, paper, glass, rubber and similar materials.
- Features an external sensor with v-groove for reliable measurement on small cylindrical parts
- Includes a set of calibration standards for ferrous and non-ferrous metals
- Supplied with a set of plastic shims or foils
- Incl. ISO Calibration Certificate
Specifications
Measuring range 0 ... 1250 µm / 0 ... 50 mils
Accuracy ± (2% + 2 µm) / ± (2% + 0.1 mils)
Resolution 0.1 µm / 0.1 mil
Operating temperatures -10 ... 50°C / 14 ... 122°F
Power 2 x 1.5V batteries
Dimensions 166 mm x 68 mm x 30 mm
6.54 in x 2.68 in x 1.18 in
Weight 0.180 kg / < 1 lb
Delivery Scope
1 x PCE-CT 27FN Coating Thickness Gauge
1 x Set of calibration standards
1 x Probe with 1 m / 3.28 ft long cable
1 x Set of plastic shims
1 x Carrying case
2 x 1.5V batteries
1 x User manual
1 x ISO calibration certificate (Optional)
- Features an external sensor with v-groove for reliable measurement on small cylindrical parts
- Includes a set of calibration standards for ferrous and non-ferrous metals
- Supplied with a set of plastic shims or foils
- Incl. ISO Calibration Certificate
Specifications
Measuring range 0 ... 1250 µm / 0 ... 50 mils
Accuracy ± (2% + 2 µm) / ± (2% + 0.1 mils)
Resolution 0.1 µm / 0.1 mil
Operating temperatures -10 ... 50°C / 14 ... 122°F
Power 2 x 1.5V batteries
Dimensions 166 mm x 68 mm x 30 mm
6.54 in x 2.68 in x 1.18 in
Weight 0.180 kg / < 1 lb
Delivery Scope
1 x PCE-CT 27FN Coating Thickness Gauge
1 x Set of calibration standards
1 x Probe with 1 m / 3.28 ft long cable
1 x Set of plastic shims
1 x Carrying case
2 x 1.5V batteries
1 x User manual
1 x ISO calibration certificate (Optional)
Coating Thickness Gauge PCE-CT 10
The material thickness gauge is used for quick and easy measurement of ink layer thicknesses on metallic surfaces. The measuring range of the material thickness gauge is between 0 ... 2.2 mm. Compared to other material thickness gauges, this material thickness gauge does not have to distinguish between ferrous and non-ferrous metals. The material thickness gauge automatically detects the substrate. Due to the measuring range and the possibility of measuring on ferrous and non-ferrous metals, the material thickness gauge covers a large part of measuring tasks.
To ensure that the material thickness gauge works, an adjustment kit is included in the delivery. As a result, an adjustment of the material thickness gauge can be performed at any time. As an additional feature, the material thickness gauge offers automatic shutdown. Thanks to this function, the replaceable battery is protected.
- Small and compact design
- For easy and quick measurement
- Digital LC display
- Automatic self-shutdown
- Adjustment with supplied standard possible
- Measuring range up to 2.2 mm
Specifications
Measuring range 0 ... 2.20 mm / 0.0 ... 86.0 mil
Resolution 0.01 mm / 0.1 mil
Accuracy In "NFe" and "Fe" modes ± 0.05 mm
In "Auto" mode
For aluminum ± (2% + 0.05 mm)
For steel ± (10% + 0.10 mm)
The accuracies relate to
To the following environmental conditions 23°C / 73.4°F ± 5°C / 9°F, < 75% RH
Ambient temperature 0 ... 40°C / 32 ... 104°F
Ambient humidity < 80% rh
Temperature coefficient 0.15x (2% of reading ± 0.05mm)
°C / °F (< 18°C / 64.4°F or > 28°C / °F)
Power supply 3V, CR 2032
Dimensions 6.9 x 3.8 x 2 cm
Weight 29 g / < 1 lb
Delivery scope
1 x Coating thickness gauge PCE-CT 10
1 x Adjustment standard
1 x NFe zero plate
1 x Button battery CR2032
1 x User manual
To ensure that the material thickness gauge works, an adjustment kit is included in the delivery. As a result, an adjustment of the material thickness gauge can be performed at any time. As an additional feature, the material thickness gauge offers automatic shutdown. Thanks to this function, the replaceable battery is protected.
- Small and compact design
- For easy and quick measurement
- Digital LC display
- Automatic self-shutdown
- Adjustment with supplied standard possible
- Measuring range up to 2.2 mm
Specifications
Measuring range 0 ... 2.20 mm / 0.0 ... 86.0 mil
Resolution 0.01 mm / 0.1 mil
Accuracy In "NFe" and "Fe" modes ± 0.05 mm
In "Auto" mode
For aluminum ± (2% + 0.05 mm)
For steel ± (10% + 0.10 mm)
The accuracies relate to
To the following environmental conditions 23°C / 73.4°F ± 5°C / 9°F, < 75% RH
Ambient temperature 0 ... 40°C / 32 ... 104°F
Ambient humidity < 80% rh
Temperature coefficient 0.15x (2% of reading ± 0.05mm)
°C / °F (< 18°C / 64.4°F or > 28°C / °F)
Power supply 3V, CR 2032
Dimensions 6.9 x 3.8 x 2 cm
Weight 29 g / < 1 lb
Delivery scope
1 x Coating thickness gauge PCE-CT 10
1 x Adjustment standard
1 x NFe zero plate
1 x Button battery CR2032
1 x User manual
Coating Thickness Measuring Device PCE-CT 25FN
The Coating Thickness Measuring Device is used for the quick and precise detection of layer thicknesses on metals. In comparison to many other paint thickness gauges, this Coating Thickness Measuring Device does not have to differentiate between ferrous and non-ferrous metal. With the small and compact design of the Coating Thickness Measuring Device, one-hand operation is possible. Despite its small size, the Coating Thickness Measuring Device has a measuring range of 1500 µm and an accuracy of ± (3% + 1 µm).
The measured values displayed can be output in µm, mm and in mils on the Coating Thickness Measuring Device. In addition to measuring the layer thickness, the Coating Thickness Measuring Device can determine the smallest, the largest and also the mean value from a series of different measurements. The Coating Thickness Measuring Device also has an automatic switch-off function.
- small and compact design
- fast measuring frequency
- Calibration set included
- Different units can be selected
- also for continuous measurements
- comfortable one-hand operation
Specifications
Measuring range 0 ... 1500 µm
Measurement accuracy ± (3% + 1 µm)
resolution 0.1 µm in the measuring range 0 ... 100 µm
1 µm in the measuring range> 100 µm
units µm, mm, mils
Smallest curvature convex 5 mm, concave 25 mm
Smallest measuring area Ø 20 mm
Minimum thickness of the substrate Fe: 0.3 mm
NFe: 0.05 mm
Measuring rate Max. 2 Hz
Power supply 9 V block battery
Operating conditions -10 ... 50 ° C, 20 ... 90% RH non-condensing
Storage conditions -10 ... 60 ° C, 20 ... 90% RH non-condensing
Dimensions 143 x 85 x 39 mm
Weight approx. 100 g
Housing material SECTION
Delivery Scope
1 x PCE-CT 25FN Coating Thickness Measuring Device
5 x calibration foil reference
1 x Fe zero standard
1 x NFe zero standard
1 x 9 V block battery
1 x instruction manual
The measured values displayed can be output in µm, mm and in mils on the Coating Thickness Measuring Device. In addition to measuring the layer thickness, the Coating Thickness Measuring Device can determine the smallest, the largest and also the mean value from a series of different measurements. The Coating Thickness Measuring Device also has an automatic switch-off function.
- small and compact design
- fast measuring frequency
- Calibration set included
- Different units can be selected
- also for continuous measurements
- comfortable one-hand operation
Specifications
Measuring range 0 ... 1500 µm
Measurement accuracy ± (3% + 1 µm)
resolution 0.1 µm in the measuring range 0 ... 100 µm
1 µm in the measuring range> 100 µm
units µm, mm, mils
Smallest curvature convex 5 mm, concave 25 mm
Smallest measuring area Ø 20 mm
Minimum thickness of the substrate Fe: 0.3 mm
NFe: 0.05 mm
Measuring rate Max. 2 Hz
Power supply 9 V block battery
Operating conditions -10 ... 50 ° C, 20 ... 90% RH non-condensing
Storage conditions -10 ... 60 ° C, 20 ... 90% RH non-condensing
Dimensions 143 x 85 x 39 mm
Weight approx. 100 g
Housing material SECTION
Delivery Scope
1 x PCE-CT 25FN Coating Thickness Measuring Device
5 x calibration foil reference
1 x Fe zero standard
1 x NFe zero standard
1 x 9 V block battery
1 x instruction manual
Coating Thickness Gauge PCE-CT 5000
The PCE-CT 5000 Coating Thickness Gauge is an instrument for a nondestructive thickness measurement of coatings, such as varnishes, paints, etc. on steel / iron and non-ferrous metals. The extremely wide measuring range of the Coating Thickness Gauge goes up to 5000 µm or 200 mils. Gumming or plastic coatings for shock and impact protection can be controlled just as the thin paint coatings. The Coating Thickness Gauge belongs to the basic equipment for each production, workshop or general quality control systems in order to control the materials at the input and output or even to show the previous paint repairs carried out on the car. Due to its compact design, it is easy to handle the device and there is a possibility of a simple one-button operation. There is also no need to set a complicated measuring mode for the individual measurements. This device automatically detects the basic surface and sets the corresponding mode. The Coating Thickness Gauge is designed and suitable for measurements of non-magnetic coatings such as varnishes, plastics, chrome, copper, zinc, enamel, etc. on steel and iron and all insulating coatings such as varnishes, plastics, enamel, paper, glass, rubber, etc. on copper, aluminum, brass and stainless steel as well as anodized aluminum.
- Measures on iron and non-ferrous metals
- Ready to measure at once
- High measuring range up to 5 mm / 0.2 in
- With different calibration standards
- Single and interval measurement
- Ergonomic one-hand operation
- Complete equipment with a battery
- Supplied with storage case
- Incl. ISO Calibration Certificate
Specification
Ferrous metals (Fe) magnetic induction
Non-ferrous metals (NFe) eddy current
Measuring range 0 µm ... 5000 µm / 0 mils ... 196.8 mils
Accuracy ±2 % or 2.5 µm / 0.1 mils (the highest value is valid)
Resolution 0.1 µm (0.0 µm ... 99.9 µm) / 0.004 mils (0.0 mils ... 4.0 mils)
1 µm (100 µm ... 5000 µm) / 0.04 mils (4.0 mils ... 200 mils)
Smallest measuring surface Ø 6 mm / Ø 0.24 in
Smallest radius of curvature convex. 5 mm / 0.2 in
concave: 60 mm / 2.4 in
Minimum thickness of the base material 0.3 mm / 0.01 in (for Fe-measurement)
0.5 mm / 0.02 in (for NFe-measurement)
Measurement modes single and interval measurement
Units µm, mils
Display lighting Yes
Environmental conditions 0° C ... +50 ° C / 32° F ... 122° F
< 80% RH
Power supply 1.5 V AAA batteries
Device dimension 129 mm x 69 mm x 27 mm
5.1 in x 2.7 in x 1.1 in
Weight 130 g / 0.3 lbs including batteries
Delivery contents
1 x PCE-CT 5000 Coating Thickness Gauge with integrated probe
1 x storage case
2 x 1.5 V AAA battery
1 x set of calibration standards
1 x user manual
1 x ISO calibration certificate (Optional)
- Measures on iron and non-ferrous metals
- Ready to measure at once
- High measuring range up to 5 mm / 0.2 in
- With different calibration standards
- Single and interval measurement
- Ergonomic one-hand operation
- Complete equipment with a battery
- Supplied with storage case
- Incl. ISO Calibration Certificate
Specification
Ferrous metals (Fe) magnetic induction
Non-ferrous metals (NFe) eddy current
Measuring range 0 µm ... 5000 µm / 0 mils ... 196.8 mils
Accuracy ±2 % or 2.5 µm / 0.1 mils (the highest value is valid)
Resolution 0.1 µm (0.0 µm ... 99.9 µm) / 0.004 mils (0.0 mils ... 4.0 mils)
1 µm (100 µm ... 5000 µm) / 0.04 mils (4.0 mils ... 200 mils)
Smallest measuring surface Ø 6 mm / Ø 0.24 in
Smallest radius of curvature convex. 5 mm / 0.2 in
concave: 60 mm / 2.4 in
Minimum thickness of the base material 0.3 mm / 0.01 in (for Fe-measurement)
0.5 mm / 0.02 in (for NFe-measurement)
Measurement modes single and interval measurement
Units µm, mils
Display lighting Yes
Environmental conditions 0° C ... +50 ° C / 32° F ... 122° F
< 80% RH
Power supply 1.5 V AAA batteries
Device dimension 129 mm x 69 mm x 27 mm
5.1 in x 2.7 in x 1.1 in
Weight 130 g / 0.3 lbs including batteries
Delivery contents
1 x PCE-CT 5000 Coating Thickness Gauge with integrated probe
1 x storage case
2 x 1.5 V AAA battery
1 x set of calibration standards
1 x user manual
1 x ISO calibration certificate (Optional)
Coating Thickness Measuring Device PCE-CT 22BT
With this Coating Thickness Measuring Device, layer thicknesses on metallic surfaces can be reliably determined. The Coating Thickness Measuring Device has a measuring range of 1500 µm. This means that the Coating Thickness Measuring Device is used, for example, in a paint shop, for incoming goods inspection or for an expert. With the Bluetooth interface on the Coating Thickness Measuring Device, all data can be transferred to a mobile iOS or Android device and exported as a CSV, PDF or TXT file. A live view with analysis of the measured values is also possible via the free app with the Coating Thickness Measuring Device.
In addition to the Bluetooth interface, the Coating Thickness Measuring Device has a micro USB interface. All data can also be transferred to the PC and analyzed via this interface in the Coating Thickness Measuring Device. Another special feature of this interface is that the Coating Thickness Measuring Device can also be operated without batteries via this interface. As a result, many measurement processes are no longer dependent on the battery charge level.
- Micro USB and Bluetooth interface
- Calibration foils included
- Adjustable alarm gene values
- Backlit display
- Data storage for up to 600 measured values
- Measuring range up to 1500 µm
Specications
Measurable substrates Fe, NFe
probe internal
measuring range 0… 1500 µm
resolution 0.1 µm (in the measuring range 0… 99.9 µm)
1 µm (in the measuring range 100… 1500 µm)
accuracy ± (1 µm + 2% of the layer thickness)
units µm, mil
Smallest curvature convex 5 mm, concave 5 mm
Smallest measuring area 10 x 10 mm
Minimum thickness of the substrate 0.4 mm
interface Bluetooth, micro USB
memory 10 groups with 60 measurements each
power supply 2 x 1.5 V AA batteries, 5 V USB interface
Environmental conditions -10… 50 ° C, 10… 85% RH
Dimensions 126 x 69 x 35 mm (without sensor)
Weight approx. 97 g (without batteries)
Delivery Scope
1 x PCE-CT 22BT Coating Thickness Measuring Device
5 x calibration foil reference
1 x Fe zero standard
1 x NFe zero standard
1 x transport loop
2 x 1.5 V AA batteries
1 x carrying case
1 x instruction manual
In addition to the Bluetooth interface, the Coating Thickness Measuring Device has a micro USB interface. All data can also be transferred to the PC and analyzed via this interface in the Coating Thickness Measuring Device. Another special feature of this interface is that the Coating Thickness Measuring Device can also be operated without batteries via this interface. As a result, many measurement processes are no longer dependent on the battery charge level.
- Micro USB and Bluetooth interface
- Calibration foils included
- Adjustable alarm gene values
- Backlit display
- Data storage for up to 600 measured values
- Measuring range up to 1500 µm
Specications
Measurable substrates Fe, NFe
probe internal
measuring range 0… 1500 µm
resolution 0.1 µm (in the measuring range 0… 99.9 µm)
1 µm (in the measuring range 100… 1500 µm)
accuracy ± (1 µm + 2% of the layer thickness)
units µm, mil
Smallest curvature convex 5 mm, concave 5 mm
Smallest measuring area 10 x 10 mm
Minimum thickness of the substrate 0.4 mm
interface Bluetooth, micro USB
memory 10 groups with 60 measurements each
power supply 2 x 1.5 V AA batteries, 5 V USB interface
Environmental conditions -10… 50 ° C, 10… 85% RH
Dimensions 126 x 69 x 35 mm (without sensor)
Weight approx. 97 g (without batteries)
Delivery Scope
1 x PCE-CT 22BT Coating Thickness Measuring Device
5 x calibration foil reference
1 x Fe zero standard
1 x NFe zero standard
1 x transport loop
2 x 1.5 V AA batteries
1 x carrying case
1 x instruction manual
Coating Thickness Gauge PCE-CT 100N
The surface tester works according to the magnetic inductive (ISO 2178) and the eddy current method (ISO 2360). These methods supported by the surface tester are used for the non-destructive testing of materials. The surface tester is used to measure the thickness of magnetically neutral layers on a magnetic or non-magnetic base material.
The surface tester is ideal for reliable layer thickness measurements on site. With the external probe, the layer thickness can be measured quickly and easily, even in hard-to-reach places. The surface tester was developed for non-destructive, fast and precise layer thickness measurements and is easy to use. Measured data can be easily transferred to a PC using a USB data storage device or via WiFi.
The surface tester is used in particular in the finishing industry, electroplating, ship and bridge construction, aircraft construction and the machine and chemical industry.
- Illuminated touch keyboard
- Measurement data storage for up to 500 data
- One-point and multi-point calibration
- Single measurement and continuous measurement
- Data transfer via wifi and USB
- Two different probes for NFe and Fe
Specification
Measuring range 0 ... 1250 µm; 0 ... 49.2 mil
Min. coating thickness of base material 50 µm
Smallest measuring surface (diameter) 10 mm
Min. radius of curvature convex 15 mm
Min. radius of curvature concave 15 mm
Accuracy ± (1% + 1 µm); ± (1% + 0.04 mil)
Resolution 0.1 µm (<99.9 µm); 0.004 mil (<3.9 mil)
1 µm (> 100 µm); 0.04 mil (> 3.9 mil)
Calibration Single point, multiple point
Data storage 500 data
Measuring modes Single measurements, continuous measurement
Interfaces Wifi , USB
Operating conditions 0 ... 50°C / 32 ... 122°F, 20 ... 90% RH non-condensing
Dimensions 170 x 85 x 35 mm / 6.7 x 3.3 x 1.4 in
Weight Approx. 335 g / < 1 lb (with battery)
Delivery Scope
1 x Coating thickness gauge PCE-CT 100N
1 x NFe probe
1 x Fe probe
1 x USB data carrier
1 x Reference film set
1 x Calibration plate (containing iron)
1 x Calibration plate (not containing iron)
2 x 1.5V AA batteries
1 x Instruction manual
The surface tester is ideal for reliable layer thickness measurements on site. With the external probe, the layer thickness can be measured quickly and easily, even in hard-to-reach places. The surface tester was developed for non-destructive, fast and precise layer thickness measurements and is easy to use. Measured data can be easily transferred to a PC using a USB data storage device or via WiFi.
The surface tester is used in particular in the finishing industry, electroplating, ship and bridge construction, aircraft construction and the machine and chemical industry.
- Illuminated touch keyboard
- Measurement data storage for up to 500 data
- One-point and multi-point calibration
- Single measurement and continuous measurement
- Data transfer via wifi and USB
- Two different probes for NFe and Fe
Specification
Measuring range 0 ... 1250 µm; 0 ... 49.2 mil
Min. coating thickness of base material 50 µm
Smallest measuring surface (diameter) 10 mm
Min. radius of curvature convex 15 mm
Min. radius of curvature concave 15 mm
Accuracy ± (1% + 1 µm); ± (1% + 0.04 mil)
Resolution 0.1 µm (<99.9 µm); 0.004 mil (<3.9 mil)
1 µm (> 100 µm); 0.04 mil (> 3.9 mil)
Calibration Single point, multiple point
Data storage 500 data
Measuring modes Single measurements, continuous measurement
Interfaces Wifi , USB
Operating conditions 0 ... 50°C / 32 ... 122°F, 20 ... 90% RH non-condensing
Dimensions 170 x 85 x 35 mm / 6.7 x 3.3 x 1.4 in
Weight Approx. 335 g / < 1 lb (with battery)
Delivery Scope
1 x Coating thickness gauge PCE-CT 100N
1 x NFe probe
1 x Fe probe
1 x USB data carrier
1 x Reference film set
1 x Calibration plate (containing iron)
1 x Calibration plate (not containing iron)
2 x 1.5V AA batteries
1 x Instruction manual
Coating Thickness Measuring Device PCE-CT 21BT
With this Coating Thickness Measuring Device, layer thicknesses on metallic surfaces can be reliably determined. The Coating Thickness Measuring Device has a measuring range of 1500 µm. This means that the Coating Thickness Measuring Device is used, for example, in a paint shop, for incoming goods inspection or for an expert. With the Bluetooth interface on the Coating Thickness Measuring Device, all data can be transferred to a mobile iOS or Android device and exported as a CSV, PDF or TXT file. A live view with analysis of the measured values is also possible via the free app with the Coating Thickness Measuring Device.
In addition to the Bluetooth interface, the Coating Thickness Measuring Device has a micro USB interface. All data can also be transferred to the PC and analyzed via this interface in the Coating Thickness Measuring Device. Another special feature of this interface is that the Coating Thickness Measuring Device can also be operated without batteries via this interface. As a result, many measurement processes are no longer dependent on the battery charge level.
- Micro USB and Bluetooth interface
- Calibration foils included
- Adjustable alarm gene values
- Backlit display
- Data storage for up to 600 measured values
- Measuring range up to 1500 µm
Specification
Measurable substrates Fe
probe external
measuring range 0… 1500 µm
resolution 0.1 µm (in the measuring range 0… 99.9 µm)
1 µm (in the measuring range 100… 1500 µm)
accuracy ± (1 µm + 2% of the layer thickness)
units µm, mil
Smallest curvature convex 5 mm, concave 5 mm
Smallest measuring area 10 x 10 mm
Minimum thickness of the substrate 0.4 mm
interface Bluetooth, micro USB
memory 10 groups with 60 measurements each
power supply 2 x 1.5 V AA batteries, 5 V USB interface
Environmental conditions -10… 50 ° C, 10… 85% RH
Dimensions 126 x 69 x 35 mm (without sensor)
Weight approx. 97 g (without batteries)
Delivery Scope
1 x PCE-CT 21BT Coating Thickness Measuring Device
5 x calibration foil reference
1 x Fe zero standard
1 x transport loop
2 x 1.5 V AA batteries
1 x carrying case
1 x instruction manual
In addition to the Bluetooth interface, the Coating Thickness Measuring Device has a micro USB interface. All data can also be transferred to the PC and analyzed via this interface in the Coating Thickness Measuring Device. Another special feature of this interface is that the Coating Thickness Measuring Device can also be operated without batteries via this interface. As a result, many measurement processes are no longer dependent on the battery charge level.
- Micro USB and Bluetooth interface
- Calibration foils included
- Adjustable alarm gene values
- Backlit display
- Data storage for up to 600 measured values
- Measuring range up to 1500 µm
Specification
Measurable substrates Fe
probe external
measuring range 0… 1500 µm
resolution 0.1 µm (in the measuring range 0… 99.9 µm)
1 µm (in the measuring range 100… 1500 µm)
accuracy ± (1 µm + 2% of the layer thickness)
units µm, mil
Smallest curvature convex 5 mm, concave 5 mm
Smallest measuring area 10 x 10 mm
Minimum thickness of the substrate 0.4 mm
interface Bluetooth, micro USB
memory 10 groups with 60 measurements each
power supply 2 x 1.5 V AA batteries, 5 V USB interface
Environmental conditions -10… 50 ° C, 10… 85% RH
Dimensions 126 x 69 x 35 mm (without sensor)
Weight approx. 97 g (without batteries)
Delivery Scope
1 x PCE-CT 21BT Coating Thickness Measuring Device
5 x calibration foil reference
1 x Fe zero standard
1 x transport loop
2 x 1.5 V AA batteries
1 x carrying case
1 x instruction manual
Coating Thickness Gauge PCE-CT 90
The coating thickness gauge is a versatile measuring instrument. This is made possible by the various optional sensors on the layer thickness gauge. For example, the coating thickness gauge can easily measure the layer thicknesses of paints, galvanic coatings, galvanizing or even anodic oxide layers on metal. With the sensors, for example, layer thickness measurements with a thickness of up to 60 mm are possible.
In addition to the layer thickness sensors for the layer thickness gauge, there is also the climate sensor. With this climate sensor at the coating thickness gauge, the ambient temperature, the ambient humidity and the dew point can be measured. Also, in the film thickness gauge, there is the surface temperature sensor. Thanks to the surface temperature sensor, the surface temperature of an object in a measuring range of -50 ... 125°C / -58 ... 257°F can be determined with the Coating Thickness Gauge.
In addition, the roughness of surfaces can be determined with the layer thickness gauge. This is made possible by the optional roughness meter. With the roughness sensor from the layer thickness gauge, the Rz value of the surface can be determined within a very short time. The measuring range here is between 0 ... 300 μm.
- Different sensors
- Measuring range up to 60 mm
- Automatic sensor detection
- Zero point and one-point calibration
- Power supply 2 x 1.5V AAA batteries
- Temperature measurement up to 125°C / 257°F
Specification
Measuring range 0 ... 60 mm; 0 ... 2.36 in.
(with M60 Senor, included)
Accuracy ± (0.03xh + 0.003) mm
(with M60 sensor, included)
Measurable materials non-magnetic layers on Fe base materials
(eg aluminum, copper)
Min. Radius of curvature 0.3 ... 50 mm; 0.012 ... 1.97 in. (depending on the sensor used)
Calibration Zero calibration, one-point calibration
Units μm, mm, °C, °F
Power supply 2 x 1.5V AAA batteries (DC)
Display Graphic display
Operating conditions -10 ... 40°C / 14 ... 104°F, 20 ... 98% r. H., non-condensing at 35°C / 95°F
Storage conditions 5 ... 40°C / 41 ... 104°F, 80% r. H., non-condensing at 25°C / 77°F
Dimensions 136 x 75 x 32 mm / 5.4 x 3 x 1.3 in
Weight 168 g / < 1 lb
Delivery Scope
1 x Coating Thickness Gauge PCE-CT 90
1 x Standard sensor PCE-CT 90-M60 incl. Calibration blocks
2 x 1.5V AAA batteries
1 x Device case
1 x ISO calibration certificate (Optional)
1 x User manual
In addition to the layer thickness sensors for the layer thickness gauge, there is also the climate sensor. With this climate sensor at the coating thickness gauge, the ambient temperature, the ambient humidity and the dew point can be measured. Also, in the film thickness gauge, there is the surface temperature sensor. Thanks to the surface temperature sensor, the surface temperature of an object in a measuring range of -50 ... 125°C / -58 ... 257°F can be determined with the Coating Thickness Gauge.
In addition, the roughness of surfaces can be determined with the layer thickness gauge. This is made possible by the optional roughness meter. With the roughness sensor from the layer thickness gauge, the Rz value of the surface can be determined within a very short time. The measuring range here is between 0 ... 300 μm.
- Different sensors
- Measuring range up to 60 mm
- Automatic sensor detection
- Zero point and one-point calibration
- Power supply 2 x 1.5V AAA batteries
- Temperature measurement up to 125°C / 257°F
Specification
Measuring range 0 ... 60 mm; 0 ... 2.36 in.
(with M60 Senor, included)
Accuracy ± (0.03xh + 0.003) mm
(with M60 sensor, included)
Measurable materials non-magnetic layers on Fe base materials
(eg aluminum, copper)
Min. Radius of curvature 0.3 ... 50 mm; 0.012 ... 1.97 in. (depending on the sensor used)
Calibration Zero calibration, one-point calibration
Units μm, mm, °C, °F
Power supply 2 x 1.5V AAA batteries (DC)
Display Graphic display
Operating conditions -10 ... 40°C / 14 ... 104°F, 20 ... 98% r. H., non-condensing at 35°C / 95°F
Storage conditions 5 ... 40°C / 41 ... 104°F, 80% r. H., non-condensing at 25°C / 77°F
Dimensions 136 x 75 x 32 mm / 5.4 x 3 x 1.3 in
Weight 168 g / < 1 lb
Delivery Scope
1 x Coating Thickness Gauge PCE-CT 90
1 x Standard sensor PCE-CT 90-M60 incl. Calibration blocks
2 x 1.5V AAA batteries
1 x Device case
1 x ISO calibration certificate (Optional)
1 x User manual